4.6L 4v Tech for the 4V Cobra motors and Mach 1

thunking & cracking

Thread Tools
 
Old Apr 28, 2005 | 09:10 PM
  #11  
SNAKEBITE's Avatar
Thread Starter
I am the post KING
 
Joined: Feb 2005
Posts: 15,244
From: Calgary
The chap beside your name I mean
Old Apr 28, 2005 | 09:44 PM
  #12  
Rondosa's Avatar
CMOC Rookie
 
Joined: Mar 2005
Posts: 30
From: Etobicoke
Originally Posted by paul
The chap beside your name I mean

oh haha. it's an abercrombie and fitch model. it's my answer to the bouncy boob avatars that drive me crazy.



edit: WO! FYI http://forums.bradbarnett.net/index.php?showtopic=22696
Old Apr 29, 2005 | 10:52 AM
  #13  
SNAKEBITE's Avatar
Thread Starter
I am the post KING
 
Joined: Feb 2005
Posts: 15,244
From: Calgary
I guess all is fair in love and war
Old Apr 30, 2005 | 04:41 PM
  #14  
Thump_rrr's Avatar
CMOC Newbie
 
Joined: Mar 2005
Posts: 11
TSB 05-9-11

FRONT SUSPENSION POPPING NOISE WHILE TURNING RIGHT OR LEFT - VEHICLES BUILT BEFORE 4/8/2005

Publication Date: April 27, 2005

FORD: 2005 Mustang


ISSUE:
Some 2005 Mustang vehicles built before 4/8/2005 may exhibit an intermittent popping noise from the front of the vehicle while turning left or right. The noise will typically occur during low speed maneuvers and may occur multiple times while turning.

ACTION:
On both sides of the vehicle, install a revised upper strut bearing assembly. If the vehicle was built before February, 2005 it may also be necessary to install a lower spring seat isolator if one is not already present. Refer to the following Service Procedure.

SERVICE PROCEDURE

Remove the strut and spring assembly. Refer to Workshop Manual Section 204-01.
Disassemble the strut and spring assembly.
If the springs do not have a rubber isolator on the bottom spring coil, install isolators. Clean off any dirt prior to installing the isolator. The isolator should be installed 4" (100 mm) from the end of the coil (Figure 1).


Figure 1 - Article 05-9-11


Reassemble the strut and spring. During reassembly, make sure the lower spring coil is butted up against the lower spring seat on the strut and the upper spring coil is butted up against the upper bearing assembly.
NOTE: INSTALL ALL NEW FASTENERS DURING REASSEMBLY.



NOTE: VEHICLE ALIGNMENT IS NOT REQUIRED AFTER THIS REPAIR.




PART NUMBER PART NAME
5R3Z-18183-A Strut Mount (Bearing)
5R3Z-5l302-A Spring Isolator
W520215S440 Strut Upper Nut
N807144S440 Stabilizer Bar Nut
W520112S440 Strut To Body Nuts
W711091S900 Strut Bolt Nuts
W709870S439 Strut Bolts


WARRANTY STATUS:
Eligible Under Provisions Of New Vehicle Limited Warranty Coverage

OPERATION DESCRIPTION TIME
050911A 2005 Mustang Install A Revised Upper Strut Bearing Assembly And A Lower Spring Seat Isolator On Both Front Struts (Do Not Use With 18124A, 18124AT, 5310A, 5310AT, 3455A, 3455AT) 1.5 Hrs.

DEALER CODING
BASIC PART NO. CONDITION CODE
18183 42
Old Apr 30, 2005 | 06:50 PM
  #15  
5PointOHNO's Avatar
CMOC Addict
 
Joined: Oct 2004
Posts: 692
From: In front of you
^your Avatar perhaps
Old Apr 30, 2005 | 07:32 PM
  #16  
SNAKEBITE's Avatar
Thread Starter
I am the post KING
 
Joined: Feb 2005
Posts: 15,244
From: Calgary
Thanks for the info. What are the chances the dealership would know about this. In the past they were replacing the part with the same defective pieces.
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
Steeda Q
Mustangs for sale
2
Sep 8, 2005 07:28 AM
Case
4.6L 4v
1
May 18, 2005 05:12 PM
Mach1 EH
Ford News
12
May 11, 2005 02:46 PM
LongHood_ShortDeck
5.0L
7
Dec 16, 2004 02:28 AM




All times are GMT -5. The time now is 02:16 AM.