1983 Ford Mustang - $14,000
4 Attachment(s)
Category: Domestic
Status: Clean Title I have a 1983 Ford Mustang for sale, in Comox Valley - British Columbia. Mileage: <2000km Engine Size: 331 Asking price is $14,000 fresh Kona Blue paint - has been wet sanded and polished to crystal clear shine. 4" Harwood pin-on w Dzus fasteners Tubular K member w G Load brace lakewood 90/10 fronts - 50/50 rears Eibach pro kit -lowers the car 1.5" in the rear - 2" in the front Flaming River manual rack with new steering shaft Lakewood lower control arms - boxed uppers completely seam welded torque boxes SLP loudmouths dumped before the axle. 6pt Maximum motorsports cage - complete with harness mounts on cross bar aftermarket bucket seats - nice and solid feel. INTERIOR dash gauge pod with 5" monster tach, Boost gauge, and voltage 3 Pod Pillar gauge pod Oil pressure (mechanincal) Water temp (mechanical) and wideband O2 sensor/meter Innovate wideband sensor with DB1 gauge what the car doesn't have - No heater core/HVAC assembly (can be reinstalled if you have one.) wiring is all there. No rear interior - I was planning on doing a custom fibreglass rear seat delete Door/belt moulding - I sent it away for paint, and buddy took off... won't answer my msgs or emails.... So I'm stuck without it :( -Engine- 331 ci currently Stock 302 block w 39,000 Km's bored .30 over Scat crank Manley H-Beam rods Probe forged pistons Ford E cam 7qt Canton pan with pickup Main Girdle - with all oiling ports champhered for optimal lubrication All ARP hardware -Heads- GT40X aluminum heads with a gasket match port and polish Upgraded dual valve springs w new valve seals -Intake- Original Cobra upper and lower intake Throttle body -Forced Air- Vortech V1 S-trim supercharger (currently pullied for 10lbs of boost) Anderson Power pipe inlet piping boscht recirculation valve Custom fabricated discharge pipe with 2 NPT fittings for Methanol injection -Additionals- Snow Methanol injection kit -Stage II progressive injection kit complete with 2gallon resevoir Stainless Steel braided line and dual nozzel injection kit -Fuel - SX performance fuel pump -10AN feed lines to fuel rails ADJ Fuel pressure regulator w mechanical fuel pressure gauge mounted under cowl. Aeromotive style fuel rails (-10AN inlets and returns) 42lb green top fuel injectors Steeda brand 90mm Mass Air Meter Upgraded rotors (slotted) and upgraded brake pads Crane Fireball HI6 ignition and coil upgraded distributor 4Core aluminum rad with electric fan on switch. Headman Hedders shorty's comes complete with ECM A9L and SCT 6-stage chip with 2 pre-loaded tunes. 3.73 gears in the rear end.... custom sumped fuel tank SX performance fuel pump -10AN fuel lines up to an adjustable regulator -aeromotive-8 style fuel rails -8 return. Extra set of weld 3.5 skinnies, strut tower braces and other goodies to go with it! Upgraded front brakes (pads, rotors and lines) Steeda clutch quadrant/firewall adj spec stage 3 clutch. Total Km`s is less than 2000km`s. asking price $14,000. I'm not willing to accept any lowball offers, however I may consider possible trades plus cash. also have a TON of extra stuff that can go with it. Power steering pump, waterpump, orig 4 eyed front end w bumper support etc feel free to email me with questions at 88hatchback (at) gmail (dot) com as I am rarely on cmoc anymore. https://www.cmoc.ca/attachment.php?a...ine=1343656314 https://www.cmoc.ca/attachment.php?a...ine=1343656314 https://www.cmoc.ca/attachment.php?a...ine=1343656314 https://www.cmoc.ca/attachment.php?a...ine=1343656314 |
All times are GMT -5. The time now is 05:55 AM. |
© 2024 MH Sub I, LLC dba Internet Brands