Car & driver pix & specs thread
Thread Starter
CMOC Elite
iTrader: (5)
Joined: Nov 2010
Posts: 1,952
From: Vineland, Ontario, Canada & Bolivar, NY
Is that Ians car ? From Beamsville ?? Sure looks like it.
1993 Mustang LX Hatch (South Carolina car)
I sold this car as a roller, and put the drivetrain into my 89 coupe.
I live up near Niagara Falls, Canada, where the winters are harsh on our vehicles. Unless you can find a vehicle that was honestly stored away during these winter months, they usually are worth nothing less than scrap. So, my search began and I found this car in 2006 from South Carolina. There were some modifications, but most have been replaced. The car had the ugly titanium interior, so that got ditched in a hurry and in went the black. The rims were replaced and new tires put on. The original owner thought that the shortblock may have given up the ghost, so I took that opportunity to replace the flimsy stock block with an FRPP R302 and fill it will goodies.
Mods include:
Motor Info:
-Hogan Racing Sheet Metal Upper Intake Manifold
-FRPP GT-40 Lower Intake Manifold w/ 1" phenolic spacer
-Siemens 75 lb low imp Injectors
-FRPP 75mm Throttle Body & EGR Spacer
-Taylor Red Race '409' Spark Plug Wires
-Aeromotive Blue Anodized Fuel Rails
-Canton 7qt. Oil Pan, Pump & Pickup
-FRPP 302R 4-Bolt Racing Block
-28 oz Fluidamper
-JE Custom Grind Forged Pistons Part #249-683
-Eagle H-Beam Forged Steel Rods Part #CRS-5400-C
-Eagle Steel Crank Part #30234005400
-File Fit Rings
-FRPP X303 Hydraulic Roller Camshaft
-Edelbrock Victor Jr Aluminum heads 2.05 intake 1.60 exhaust stud mnt
-Trick Flow Hardened Push Rods 6.250 .080
-Speed Pro 1.6 Roller Rockers
-Moroso Sheet Metal Valve Covers
-Vortech YSI Trim Supercharger (13psi-28psi)
-Anderson Power Pipe
-80mm Pro-M Mass Air Meter
-K&N Conical Air Filter
-ARP Bolts throughout engine
-Canton Aluminum Coolant Tank Overflow
-Ron Davis 4-Core Radiator
-Energy Suspension Solid Engine Mounts
-FRPP 28 ounce Steel Billet flywheel
Exhaust:
-Kooks 2” LT headers
-Custom 3 ½”” Dr. Gas X pipe
-Borla XR-1 Mufflers
Electronics:
-Anderson PMS series 4 w/low imp injector driver and 3 bar map sensor
-MSD 6AL Ignition
-MSD Blaster Coil
Chassis:
-TRZ Through the floor sub frame connectors
-S & W 8-Point Roll Cage - NHRA Certified
-UPR Double Adjustable Upper/Lower Control Arms
-Hal Adjustable Front Coil Over Struts
-QA1 Rear Shocks
-Welded Tourque boxes
-Moroso Battery Box and relocation Kit
-D&D Castor/Camber Plates (Front)
-Flaming River Manual Steering Rack, Shaft & Bump Steer kit
-D&D Tubular Front K-Member w/Tubular A-Arms
Drivetrain:
-Weld Pro Stars - Front 15 x 3.5 with 165 Tires
-Weld Pro Stars - Rear 15 x 10 w/6.5" B.S.
-Mickey Thompson ET Street 28 x 12.5 x 15
-Spec Stage 3 HD Clutch
-Lakewood Scattershield
-Tremec 3550 HD Racing Transmission
-FRPP Aluminum Driveshaft
-HP Motorsports Driveshaft Safety Loop
-31 Spline Moser Axles
-Full Spool
-FRPP 3.73 Gears
-5-Lug Conversion Front Disc Brake Set
-8.8 Rear end Girdle
Interior:
-Complete black interior swap from mint condition donor car
-Autometer Liquid Filled Sport Comp Oil Pressure Gauge
-Autometer Liquid Filled Sport Comp Temperature Gauge
-Autometer Liquid Filled Sport Comp Boost Gauge
-Autometer Sport Comp Fuel Pressure Gauge
-Autometer Gauge Cage
-Autometer 5" Monster Tach w/Shift light and recall
-Pro - 5.0 Power Tower Shifter
-Pioneer 6 x 9 Speakers located in rear
-Pioneer 4" Speakers located in the doors
-Alpine CD player
-Mac Cobra White Faced Gauges
Exterior:
-4" Cervini's Cowl Hood
-6-piece Diamond Headlight Set
-Factory Ford Rear Tail Lamps
-Factory Ford Rear Quarter Glass
-Factory Ford Rubber Sealing around doors
Fuel System:
-Aeromotive "Eliminator" fuel pump
-Aeromotive in-line filter
-FRPP 290 lph Fuel pump inside tank
-#8 Braided line front to back
-Aeromotive 3-port Fuel Pressure Regulator
-#6 Braided line from Regulator to Fuel Rails
-All lines using Russel Anodized Fittings
Misc.:
-Mac Aluminum Pedals
-Moroso Battery Cut-Off Switch
-Viper Car Alarm
I sold this car as a roller, and put the drivetrain into my 89 coupe.
I live up near Niagara Falls, Canada, where the winters are harsh on our vehicles. Unless you can find a vehicle that was honestly stored away during these winter months, they usually are worth nothing less than scrap. So, my search began and I found this car in 2006 from South Carolina. There were some modifications, but most have been replaced. The car had the ugly titanium interior, so that got ditched in a hurry and in went the black. The rims were replaced and new tires put on. The original owner thought that the shortblock may have given up the ghost, so I took that opportunity to replace the flimsy stock block with an FRPP R302 and fill it will goodies.
Mods include:
Motor Info:
-Hogan Racing Sheet Metal Upper Intake Manifold
-FRPP GT-40 Lower Intake Manifold w/ 1" phenolic spacer
-Siemens 75 lb low imp Injectors
-FRPP 75mm Throttle Body & EGR Spacer
-Taylor Red Race '409' Spark Plug Wires
-Aeromotive Blue Anodized Fuel Rails
-Canton 7qt. Oil Pan, Pump & Pickup
-FRPP 302R 4-Bolt Racing Block
-28 oz Fluidamper
-JE Custom Grind Forged Pistons Part #249-683
-Eagle H-Beam Forged Steel Rods Part #CRS-5400-C
-Eagle Steel Crank Part #30234005400
-File Fit Rings
-FRPP X303 Hydraulic Roller Camshaft
-Edelbrock Victor Jr Aluminum heads 2.05 intake 1.60 exhaust stud mnt
-Trick Flow Hardened Push Rods 6.250 .080
-Speed Pro 1.6 Roller Rockers
-Moroso Sheet Metal Valve Covers
-Vortech YSI Trim Supercharger (13psi-28psi)
-Anderson Power Pipe
-80mm Pro-M Mass Air Meter
-K&N Conical Air Filter
-ARP Bolts throughout engine
-Canton Aluminum Coolant Tank Overflow
-Ron Davis 4-Core Radiator
-Energy Suspension Solid Engine Mounts
-FRPP 28 ounce Steel Billet flywheel
Exhaust:
-Kooks 2” LT headers
-Custom 3 ½”” Dr. Gas X pipe
-Borla XR-1 Mufflers
Electronics:
-Anderson PMS series 4 w/low imp injector driver and 3 bar map sensor
-MSD 6AL Ignition
-MSD Blaster Coil
Chassis:
-TRZ Through the floor sub frame connectors
-S & W 8-Point Roll Cage - NHRA Certified
-UPR Double Adjustable Upper/Lower Control Arms
-Hal Adjustable Front Coil Over Struts
-QA1 Rear Shocks
-Welded Tourque boxes
-Moroso Battery Box and relocation Kit
-D&D Castor/Camber Plates (Front)
-Flaming River Manual Steering Rack, Shaft & Bump Steer kit
-D&D Tubular Front K-Member w/Tubular A-Arms
Drivetrain:
-Weld Pro Stars - Front 15 x 3.5 with 165 Tires
-Weld Pro Stars - Rear 15 x 10 w/6.5" B.S.
-Mickey Thompson ET Street 28 x 12.5 x 15
-Spec Stage 3 HD Clutch
-Lakewood Scattershield
-Tremec 3550 HD Racing Transmission
-FRPP Aluminum Driveshaft
-HP Motorsports Driveshaft Safety Loop
-31 Spline Moser Axles
-Full Spool
-FRPP 3.73 Gears
-5-Lug Conversion Front Disc Brake Set
-8.8 Rear end Girdle
Interior:
-Complete black interior swap from mint condition donor car
-Autometer Liquid Filled Sport Comp Oil Pressure Gauge
-Autometer Liquid Filled Sport Comp Temperature Gauge
-Autometer Liquid Filled Sport Comp Boost Gauge
-Autometer Sport Comp Fuel Pressure Gauge
-Autometer Gauge Cage
-Autometer 5" Monster Tach w/Shift light and recall
-Pro - 5.0 Power Tower Shifter
-Pioneer 6 x 9 Speakers located in rear
-Pioneer 4" Speakers located in the doors
-Alpine CD player
-Mac Cobra White Faced Gauges
Exterior:
-4" Cervini's Cowl Hood
-6-piece Diamond Headlight Set
-Factory Ford Rear Tail Lamps
-Factory Ford Rear Quarter Glass
-Factory Ford Rubber Sealing around doors
Fuel System:
-Aeromotive "Eliminator" fuel pump
-Aeromotive in-line filter
-FRPP 290 lph Fuel pump inside tank
-#8 Braided line front to back
-Aeromotive 3-port Fuel Pressure Regulator
-#6 Braided line from Regulator to Fuel Rails
-All lines using Russel Anodized Fittings
Misc.:
-Mac Aluminum Pedals
-Moroso Battery Cut-Off Switch
-Viper Car Alarm
