T5 with Hardened Gears
12-03-2005, 07:41 PM
#1
CMOC Newbie
Thread Starter
Join Date: Jul 2005
Location: peterborough
Posts: 19
T5 with Hardened Gears
This is a rebuilt Used T5 Tranny. It was rebuilt with new synchros, and hardened gears, and only used for about 2 months.
It has a Hurst short throw shifter on it, I can easily separate them, or it can go with the tranny.
Its been sitting in my garage for 6 months, as a spare.
I have never used it, It was included in some other parts I bought.
It seems to shift fine,( on the bench), and the guy I got it from was honest.
There are no cracks in the case, and it is very clean.
PM or Email at bsl89lx@yahoo.com.
$250
It has a Hurst short throw shifter on it, I can easily separate them, or it can go with the tranny.
Its been sitting in my garage for 6 months, as a spare.
I have never used it, It was included in some other parts I bought.
It seems to shift fine,( on the bench), and the guy I got it from was honest.
There are no cracks in the case, and it is very clean.
PM or Email at bsl89lx@yahoo.com.
$250
12-03-2005, 09:17 PM
#2
CMOC Veteran
Join Date: Dec 2004
Location: Lidsville, Ontario, Canada
Posts: 407
[QUOTE=BSL]This is a rebuilt Used T5 Tranny. It was rebuilt with new synchros, and hardened gears, and only used for about 2 months.
It has a Hurst short throw shifter on it, I can easily separate them, or it can go with the tranny.
Its been sitting in my garage for 6 months, as a spare.
I have never used it, It was included in some other parts I bought.
It seems to shift fine,( on the bench), and the guy I got it from was honest.
There are no cracks in the case, and it is very clean.
PM or Email at bsl89lx@yahoo.com.
$250
The rebuild.... Is it a 3.35 1st gear gearset or 2.95 gearset? Who did the rebuild? Does it have the upgraded throwout bearing retainer? How much w/o the Hurst shifter?
It has a Hurst short throw shifter on it, I can easily separate them, or it can go with the tranny.
Its been sitting in my garage for 6 months, as a spare.
I have never used it, It was included in some other parts I bought.
It seems to shift fine,( on the bench), and the guy I got it from was honest.
There are no cracks in the case, and it is very clean.
PM or Email at bsl89lx@yahoo.com.
$250
The rebuild.... Is it a 3.35 1st gear gearset or 2.95 gearset? Who did the rebuild? Does it have the upgraded throwout bearing retainer? How much w/o the Hurst shifter?
12-03-2005, 09:34 PM
#3
CMOC Newbie
Thread Starter
Join Date: Jul 2005
Location: peterborough
Posts: 19
Originally Posted by Schlodes
The rebuild.... Is it a 3.35 1st gear gearset or 2.95 gearset? Who did the rebuild? Does it have the upgraded throwout bearing retainer? How much w/o the Hurst shifter?
I geuss I could try to find out the 1st gearset ratio...by counting the turns. Ill get back to you on that.
I'll knock 20$ off without the shifter, or just make an offer.
BTW-I would be asking a lot more for it, if I knew the details 100%- I know what a good rebuilt T5 goes for, unfortunately, I dont have the paperwork for this one.
12-03-2005, 10:13 PM
#5
CMOC Veteran
Join Date: Dec 2004
Location: Lidsville, Ontario, Canada
Posts: 407
Did he say where he bought the hardened gears from? What ALL did he tell you? I've just bought more than my sahre of used T5s that are not any good, and if this has never been in a car....... well.. you see where I am going... 
Yeah if you dont mind count how many turns it takes the input shaft to rotate to get 1 full roation of the output shaft with the trans in 1st gear.
Yeah if you dont mind count how many turns it takes the input shaft to rotate to get 1 full roation of the output shaft with the trans in 1st gear.
12-03-2005, 10:47 PM
#6
CMOC Newbie
Thread Starter
Join Date: Jul 2005
Location: peterborough
Posts: 19
This Trans HAS been in a car, I think that was in my first post. It was pulled in favour of an Auto, and more consistant times.
Like I said, I dont know who built it, and I dont have any paperwork. I trust the guy I got it from, he would never commission a halfass rebuild.
If you have any more questions, or would like to take a look, please feel free to email me at bsl89lx@yahoo.com. If you are serious, I will give you my phone #.
Thank you for your interest
Like I said, I dont know who built it, and I dont have any paperwork. I trust the guy I got it from, he would never commission a halfass rebuild.
If you have any more questions, or would like to take a look, please feel free to email me at bsl89lx@yahoo.com. If you are serious, I will give you my phone #.
Thank you for your interest
12-04-2005, 02:12 PM
#7
CMOC Newbie
Join Date: Sep 2005
Posts: 19
interested in any types of trades? stormin normin hood, hatch or exhaust?
12-05-2005, 01:54 PM
#10
CMOC Newbie
Thread Starter
Join Date: Jul 2005
Location: peterborough
Posts: 19
Originally Posted by 94StangGT
Which year was this out of? Do you know if it will fit 94 GT? Thanks
I know for sure it fits 86-93. You would have to make sure '94 shares the same tranny as '93.
