Ford Racing Gears...be Careful
FRP gears
08-07-2006, 01:08 AM
#45
Since were on the topic or gears and rear ends who here has changed there own gears before? well I desided to be a brave soul and try to save some money and upgrade my gears from 2.73 to stock ford 3.27's well all said and done now my rearend howls, now come to find out that you have to "shim" the gears :2: this is so not good what and were do I have to shim were do I get shims this is very gay 
someone direct me to were im suppose to go with this im going to have to rip them back out and redo it could yous some real god advice and possibly some pics??? the 3.27's came out of the same car as mine but automatic
someone direct me to were im suppose to go with this im going to have to rip them back out and redo it could yous some real god advice and possibly some pics??? the 3.27's came out of the same car as mine but automatic
08-07-2006, 09:36 AM
#46
You should check the mesh and blacklash, it is not as simple as just installing.
Here are some sites
http://www.corral.net/tech/drivetrain/gears.html
http://www.precisiongear.com/pgtechpatterns.htm
http://www.differentials.com/install.html
Here are some sites
http://www.corral.net/tech/drivetrain/gears.html
http://www.precisiongear.com/pgtechpatterns.htm
http://www.differentials.com/install.html
08-07-2006, 10:10 AM
#47
I will bet the thread started due to an improper gear installation. I am sure he believes in his installers 'talents' however too many people including myself have installed the newer gears to reaffirming there is nothing wrong with them.
If the gears were indeed bad (a manufacture defect) then it should have been caught during installation. If it was a bad set of gears (a material defect) and they wore improperly then when it was torn apart there should be proof of this.
It sounds like the backlash was only checked in one spot on the ring gear. The min. you should ever check it is in 3 spots around the ring gear and better yet is 4 in a cross pattern. Acceptable run-out is usually around +/- .002" and most gear sets I have installed have less then .001".
Generally if the backlash is within spec, the pinion is pre-loaded properly and the gear pattern is right for your application then more then likely you will be just fine. The harder you will be on the gear set (i.e.: drag racing) the more precise the install must be.
If the gears were indeed bad (a manufacture defect) then it should have been caught during installation. If it was a bad set of gears (a material defect) and they wore improperly then when it was torn apart there should be proof of this.
It sounds like the backlash was only checked in one spot on the ring gear. The min. you should ever check it is in 3 spots around the ring gear and better yet is 4 in a cross pattern. Acceptable run-out is usually around +/- .002" and most gear sets I have installed have less then .001".
Generally if the backlash is within spec, the pinion is pre-loaded properly and the gear pattern is right for your application then more then likely you will be just fine. The harder you will be on the gear set (i.e.: drag racing) the more precise the install must be.
11-19-2006, 02:55 PM
#49
CMOC Rookie
Join Date: Aug 2006
Location: hamilton
Posts: 121
just talked to a friend of mine Hes the shop forman at erinwood ford. He said that there is no difereance in set up from the old to the new part# maby the installer just had a bad day It dose happen you know
11-20-2006, 06:20 PM
#50
CMOC Elite
Join Date: Oct 2005
Location: blackfalds, ab
Posts: 1,589
Originally Posted by Terminal Velocity
Santa told me hes bringing me FR 4.10's for christmas ill have to leave milk and cookies out for her lol
hopefully the install/shim kit too!
hopefully the install/shim kit too!
