Canadian Mustang Owners Club - Ford Mustang Forums

Canadian Mustang Owners Club - Ford Mustang Forums (https://www.cmoc.ca/)
-   Mustang Drivetrain (https://www.cmoc.ca/mustang-drivetrain-87/)
-   -   quad shock with 275's (https://www.cmoc.ca/mustang-drivetrain-87/quad-shock-275s-17635/)

borbet 07-28-2012 07:20 AM

Agree with 1990. Our cars flex in the middle due to the unibody design of the times , todays cars are so far advanced in chassis stiffness. I would recommend frame connectors as a starting point to stiffen the car up and then look at matching struts / shocks / springs at those kms it is time . Then toss quad shocks in thrash can . lol

Do you have any goals for this car ?

dreo26 07-29-2012 01:53 AM

No goals specifically, but im always wanting to do something more!I think i'll look into frame connectors
Thanks

borbet 07-30-2012 01:32 PM

They can be aftermarket or some square or rectangle tubing from a local metal supply house . Most metal supply sell at 20 to 24 foot lengths , some will sell short sections .

Let us know how it is when you get them done .

dreo26 07-30-2012 08:29 PM

Is there a certain way to install these? I know when my car is on the hoist the doors dont close properly, will installing the frame connectors hold the body flexed in that position?

borbet 08-02-2012 07:09 AM

Yes ! They are welded in to each end of the frames with some flatstock brackets to tie welded areas together . Then prime , paint or undercoat as desired.

Your last statment has me concerned .... doors wont close right on a hoist .

How rusty is the bottom of your car ? If and i say if it is not rusty i would be looking very close for rips in the floors sheet metal at all suspension points and where rear seat dogleggs to floor . Power shifting and time with rough roads take its toll on uni - body cars .

This past winter i was doing front sway bar bushings / links and a water pump due to a small leak ....... I found one small rust hole in a rocker along with 3 small rips in the floors sheet metal . Now it has new ceramic hedders exhaust motor mounts aluminum rad electric fan new carpets battery in trunk 3 G rewired with kill switch stereo rewired new speakers sound deadner etc ...... once ya start it can snowball :D
P.S. I have a loving wife . $$$$$$

dreo26 08-05-2012 04:05 PM

The car does not have any rust or a single hole in the floors, I just assembled the car so i am sure of it. when I say they won't close properly I mean not perfectly should I still be concerned? any other spots I should look?

borbet 08-10-2012 04:51 AM

Could be just the way it was on the hoist ??? but again do frame connectors and you will be impressed .
If it still feels soft to you after then look at any wear items that need to be done next . ie struts , bushings etc .

dreo26 08-29-2012 07:54 PM

You may be right about how it was on the hoist because yesterday we had it up on the hoist and the drivers door operated with no trouble.
i have some square tubing and plates, im goung to weld them up as soon as i get some time

borbet 08-30-2012 03:09 PM

Sounds great . Make sure it is level at all four corners and look at all gaps on doors before you mig .
Best darn mod for any fox .

Since you have time , wanna finnish my heater core ?? lol

1990Fox 09-03-2012 01:13 AM

Heater cores are fun to do lol ;) I've done 2 of them so far


All times are GMT -5. The time now is 08:33 AM.


© 2024 MH Sub I, LLC dba Internet Brands