Turbo installation

Reply Subscribe

Thread Tools

Oct 15, 2006 | 11:42 AM

#11

silverbullet

CMOC Rookie

Joined: Jun 2006

Posts: 79

From: London,Ont./ Cochrane,Ab.

which web site did you attain this info from ???

Oct 15, 2006 | 12:24 PM

#12

dice

Thread Starter

CMOC Veteran

Joined: Jul 2006

Posts: 287

From: Trenton

Quote:

Originally Posted by silverbullet

which web site did you attain this info from ???

Got it from some forum when I was surfing the web. I just googled it. I can't remember the name of the site. I have all this saved on my PC.

Oct 15, 2006 | 12:36 PM

#13

dice

Thread Starter

CMOC Veteran

Joined: Jul 2006

Posts: 287

From: Trenton

Quote:

Originally Posted by Speedtospare

its cheaper to order a kit. 99% of people will not go an buy a welder and all the proper stuff needed to make a turbo kit. I have made my own twice now. I just order a new hotside and I found it just as cheap and easier to order a hot side. Hot side can be purchased for 550 US from soe companies.

You got to be kidding. Show me where you got your turbo kit, cause I have been looking for a while now. A good Kit on ebay runs about $3000.00. If I buy piece by piece I am looking at saving about a grand. The turbo alone is $250 without the intercooler and piping. Not to mention i need twins, so that is $500.00 just for turbo's. And that is on ebay. Not from the shop. I am seriously thinking of installing turbo's and I have been looking into this for a while. Where did you buy your stuff?

Oct 15, 2006 | 01:00 PM

#14

White97

CMOC Elite

Joined: Nov 2004

Posts: 1,614

From: .

$250 for a turbo? Lucky.

A VNT17 will cost me around $1000 US for my TDI...

Oct 15, 2006 | 01:03 PM

#15

dice

Thread Starter

CMOC Veteran

Joined: Jul 2006

Posts: 287

From: Trenton

LOL. That is for a T3 Hybrid. Not even sure if it is a good one. For the price, Probably not.

Oct 15, 2006 | 11:26 PM

#16

l8/93lx

CMOC Rookie

iTrader: (2)

Joined: Mar 2006

Posts: 95

From: Windsor

Two good companies, check out their sites and on turbomustangs.com
I have a single turbo hot side setup on order from pony down, right from the exhaust flange to the cat-back.
B&G turbo
http://www.bgturbokits.com/store/
Pony Down Performance
http://ziptie007.phpwebhosting.com/c...ain_page=index

Dec 26, 2013 | 01:00 AM

#17

bman_t3@hotmail.com

CMOC Rookie

Joined: Aug 2013

Posts: 33

From: Moose Jaw, Saskatchewan

This honestly was the most comprehensive and simplest guide I have read across the net, Thank you very much for putting the time into this to make it happen. I was also in the question for the 3.8 V6 setup. If there is a similar thread to this for that, in addition I've been looking all over the place to find the factory intake manifold that has the split port induction and no luck anywhere. Nothing aftermarket it seems either.

Dec 26, 2013 | 07:23 AM

#18

Apocalypse Pony

Adminut

Joined: May 2009

Posts: 5,722

From: Maple Tree, Branch #2 above the rope swing

Awesome, you had to really put on your archeological dig hat to find that one. I think seven years old is a record, but good info is good info, glad you found it. lol